OBSERVATION_FILE_NAME=OCT2009.OPE OBSERVATION_FILE_TYPE=OPE OBSERVATION_START_DATE=2009.10.27 OBSERVATION_START_TIME=18:00:00 OBSERVATION_END_DATE=2009.10.28 OBSERVATION_END_TIME=07:00:00

DEF_FMOS_SPEC=OBE_ID=FMOS OBE_MODE=SPEC DEF_FMOS_SUBR=OBE_ID=FMOS OBE_MODE=SUBROUTINE SF_NGC6633=S2O=CLU_NGC6633_MAPE.S2O MAXIT_HOME=0 MAXIT_OBJ=0 SF_SSA22=S2O=SSA22_FMOS_OBS_091006.S2O MAXIT_HOME=1 MAXIT_OBJ=7 NCH=3 SF_SXDS1=S2O=SXDS_TARGETS1_BS.S2O SF_SXDS2=RA=!STATS.RA DEC=!STATS.DEC EQUINOX=2000 INSROT_PA=0 S2O=HOME.S2O MAXIT_HOME=1 MAXIT_OBJ=1 SF_SXDS3=S2O=HOME.S2O MAXIT_HOME=1 MAXIT_OBJ=1 BS_SXDS1=OBJECT=SXDS CROSS=0 BS_DRA1=1 BS_DDEC1=2 NCH=1 NBS=2 NEXP1=1 EXPTIME1=900 MODE1=RAMP BS_SXDS2=S2O=SXDS.S2O NCH=1 NBS=2 NEXP1=1 EXPTIME1=900 MODE1=RAMP OBJ=OBJECT=TEST # Simple communication test with OBCP. Usually unnecessary. EXEC FMOS OBCP_MODE MODE=ALIVE EXEC FMOS OBCP_MODE MODE=FREE ######################################################################## # Recommended to execte below for tests in the evening. # Also run "INIT TAKO" (FMOS tab) from Launcher for reference procedure. ######################################################################## EXEC FMOS ECH_FI_SPINE SPINEID=123 EXEC FMOS ECH_CONFIGURE_FIELD FILENAME=HOME.S2O STARTTMOFOBS=0 OBSDURATION=0 MAXITERATIONS=2 RMS=0 SLEW=1 GETOBJECTN $DEF_FMOS_SPEC NEXP1=2 EXPTIME1=0 MODE1=CDS NEXP2=2 EXPTIME2=0 MODE2=CDS GETOBJECTN $DEF_FMOS_SPEC NEXP1=2 EXPTIME1=60 MODE1=RAMP NEXP2=2 EXPTIME2=60 MODE2=RAMP ########################################### # Other commands possibly useful for tests. ########################################### ## IRS1 Messia initialization EXEC FMOS IRS1_HAWAII_INIT ## IRS1 single CDS exposure: execute the next two lines at once. EXEC FMOS IRS1_HAWAII_EXPOSURE FRAMEID=AUTO EXPTIME=0 MODE=CDS OBJECT=TEST EXEC FMOS IRS1_EXP_CMPL ## IRS2 single CDS exposure: execute the next two lines at once. EXEC FMOS IRS2_HAWAII_EXPOSURE FRAMEID=AUTO EXPTIME=0.001 MODE=CDS NUM_EXP=1 NUM_SAMPLES=2 OBJECT=TEST EXEC FMOS IRS2_EXP_CMPL ## IRS1 single CDS/RAMP exposure: using GETOBJECT1 GETOBJECT1 $DEF_FMOS_SPEC NEXP=1 EXPTIME=0 MODE=CDS OBJECT=TEST GETOBJECT1 $DEF_FMOS_SPEC NEXP=1 EXPTIME=60 MODE=RAMP OBJECT=TEST ## IRS2 single CDS/RAMP exposure: using GETOBJECT2 GETOBJECT2 $DEF_FMOS_SPEC NEXP=1 EXPTIME=0 MODE=CDS OBJECT=TEST GETOBJECT2 $DEF_FMOS_SPEC NEXP=1 EXPTIME=60 MODE=RAMP OBJECT=TEST ## TAKO initialization ## Why don't you do these all from Launcher?? EXEC FMOS TAKO_CMM_REF_PROC EXEC FMOS TAKO_FAM_REF_PROC EXEC FMOS TAKO_AG_SH_REF_PROC ## Test if the necessary info is extracted from a .s2o file. TESTS2O $DEF_FMOS_SPEC S2O=SSA22_FMOS_OBS_091006.S2O ################################## # Commands for on-sky observation. ################################## ## Focus check EXEC FMOS ECH_CHECK_FOCUS S2O=CLU_NGC6633_MAPE.S2O MINFOC=4.5 MAXFOC=5.1 NPOINTS=7 ## SXDS OBSERVATION SETUPFIELD3 $DEF_FMOS_SPEC $SF_SXDS1 MAXIT_HOME=0 MAXIT_OBJ=7 NCH=3 SETUPFIELD3 $DEF_FMOS_SPEC $SF_SXDS1 MAXIT_HOME=0 MAXIT_OBJ=0 NCH=3 GETOBJECT1 $DEF_FMOS_SPEC NEXP=1 EXPTIME=900 MODE=RAMP OBJECT=SXDS_TARGET1 GETOBJECT1 $DEF_FMOS_SPEC NEXP=1 EXPTIME=900 MODE=RAMP OBJECT=SXDS_TARGET1_SKY BEAMSWITCH2 $DEF_FMOS_SPEC $SF_SXDS1 NCH=1 NBS=2 NEXP1=1 EXPTIME1=900 MODE1=RAMP NEXP2=1 EXPTIME2=900 MODE2=RAMP ## SSA22 OBSERVATION SETUPFIELD3 $DEF_FMOS_SPEC S2O=SSA22_FMOS_OBS_091006.S2O MAXIT_HOME=1 MAXIT_OBJ=7 NCH=3 SETUPFIELD3 $DEF_FMOS_SPEC S2O=SSA22_FMOS_OBS_091006.S2O MAXIT_HOME=0 MAXIT_OBJ=0 NCH=3 GETOBJECT1 $DEF_FMOS_SPEC NEXP=1 EXPTIME=900 MODE=RAMP OBJECT=SSA22 GETOBJECT1 $DEF_FMOS_SPEC NEXP=1 EXPTIME=900 MODE=RAMP OBJECT=SSA22_SKY BEAMSWITCH2 $DEF_FMOS_SPEC S2O=SSA22_FMOS_OBS_091006.S2O NCH=1 NBS=2 NEXP1=1 EXPTIME1=900 MODE1=RAMP NEXP2=1 EXPTIME2=900 MODE2=RAMP ## Rastering TELRASTER55 $DEF_FMOS_SPEC DITH=1.0 EXPTIME1=60 EXPTIME2=60 OBJECT=RASTER_ON_N6633 ########################################################################### # Data acquisition for calibration & alignment. # NOTE: GETOBJECTN will need to be used on Oct 27-29 instead of GETOBJECT1. ########################################################################### ## CAL lamp (ThAr, P2(Front)) ON/OFF ## Why don't you do this from Launcher?? ## NOTE: "FeAr" shows ON/OFF on IntegGUI but don't worry. EXEC TSC CAL_SOURCE MOTOR=ON F_SELECT=P_IR LAMP=HCT1 AMP=15 ## DOMEFLAT 4X600W (--> reduced to 60V) NO TOP SCREEN ## For IRS1 LR, 30000 ADUs at the bright end. GETOBJECT1 $DEF_FMOS_SPEC NEXP=10 EXPTIME=20 MODE=CDS OBJECT=DOMEFLAT ## THAR CAL LAMP 15MA NO TOP SCREEN ## For IRS1 LR GETOBJECT1 $DEF_FMOS_SPEC NEXP=1 EXPTIME=20 MODE=CDS OBJECT=THARLAMP GETOBJECT1 $DEF_FMOS_SPEC NEXP=1 EXPTIME=40 MODE=CDS OBJECT=THARLAMP